Solved-Programming Assignment 4: Circuit Simulator- Solution

Description

You have to write a circuit simulator. One of the inputs to your program will be a circuit description le that will describe a circuit using various directives. Your program will print the output of the circuit for all possible input values.

1 Circuit Description Directives

The input variables used in the circuit are provided using the INPUTVAR directive. The INPUTVAR directive is followed by the number of input variables and the names of the input variables. All the input variables will be named with capitalized identi ers. An identi er consists of at least one character (A-Z) followed by a series of zero or many characters (A-Z) or digits (0-9). For example, some identi ers are IN1, IN2, and IN3. An example speci cation of the inputs for a circuit with three input variables: IN1, IN2, IN3 is as follows:

INPUTVAR 3 IN1 IN2 IN3

The outputs produced by the circuit is speci ed using the OUTPUTVAR directive. The OUTPUTVAR directive is followed by the number of outputs and the names of the outputs.

An example speci cation of the circuit with output OUT1 is as follows:

OUTPUTVAR 1 OUT1

The circuits used in this assignment will be built using the following building blocks: NOT, AND, OR, NAND, NOR, and XOR.

The building blocks can produce temporary variables as outputs, and can use either the input variables or temporary variables as input. Output variables will never be used as inputs in a building block.

All the temporary variables will also be named with lower case identi ers (i.e., temp1, temp2, temp3, …).

The speci cation of each building block is as follows:

NOT: for example, NOT IN1 OUT1

AND: for example, AND IN1 IN2 OUT1

OR: for example, OR IN1 IN2 OUT1

NAND: for example,

1

NAND IN1 IN2 OUT1

NOR: for example, NOR IN1 IN2 OUT1

XOR: for example, XOR IN1 IN2 OUT1

2 Describing Circuits using the Directives

It is possible to describe any combinational circuit using the above set of directives. For example, the circuit

OUT1 = IN1.IN2 + IN1.IN3 can be described as follows:

INPUTVAR 3 IN1 IN2 IN3

OUTPUTVAR 1 OUT1

AND IN1 IN2 temp1

AND IN1 IN3 temp2

OR temp1 temp2 OUT1

Note that OUT1 is the output variable. IN1, IN2, and IN3 are input variables. temp1 and temp2 are temporary variables.

A circuit description is a sequence of directives. You can assume that every temporary variable occurs as a output variable in the sequence before occurring as an input variable.

Note: A temporary variable can occur as an output variable in at most one directive.

3 Format of the Input Files

Your program will be given one le as input, containing the description of a circuit using the directives described above.

For example:

INPUTVAR 3 IN1 IN2 IN3

OUTPUTVAR 1 OUT1

AND IN1 IN2 temp1

AND IN1 IN3 temp2

OR temp1 temp2 OUT1

4 The problem

You have to write a program called first as described above. You are guaranteed that the circuit descriptions given as input to your program will be sorted. Let’s look at an example we have encountered before.

Example Execution

Suppose a circuit description le named circuit.txt has the description for the circuit OUT1 = IN1.IN2 + IN1.IN3

2

INPUTVAR 3 IN1 IN2 IN3

OUTPUTVAR 1 OUT1

AND IN1 IN2 temp1

AND IN1 IN3 temp2

OR temp1 temp2 OUT1

Then, on executing the program with the above circuit description le, your program should produce the following output:

./first circuit.txt

0000

0010

0100

0110

1000

1011

1101

1111

The output of the rst three columns are INPUTVAR IN1, IN2, and IN3 respectively. And the last column denotes the OUTPUTVAR OUT1.

Note: the values of the input and output variables should be space separated and be in the same order as the output variables in the INPUTVAR and OUTPUTVAR directive, e.g., if the circuit description le has the directive INPUTVAR 3 IN1 IN2 IN3, and OUTPUTVAR 3 OUT1 OUT2 OUT3, then the rst values should be those of the input variables IN1, IN2, and IN3, and output variable OUT1, followed by that of OUT2, and then that of OUT3.

5 Submission

Please submit a tar le named pa4.tar on Canvas. To create this le, put everything that you are submitting into a directory (folder) named pa4. Then, cd into the directory containing pa4 (that is, pa4’s parent directory) and run the following command:

tar cvf pa4.tar pa4

To check that you have correctly created the tar le, you should copy it (pa4.tar) into an empty directory and run the following command:

tar xvf pa4.tar

This should create a directory named pa4 in the (previously) empty directory.

The pa4 directory in your tar le must contain one subdirectory. The subdirectory should be named rst (in lower case). Each directory should contain your source les, header les, and a make le. Running the make le in the rst folder, should produce the binary rst.

Use the autograder to test your submission during development and before submission as you had done with your other assignments.

3